W

HOME PAGE

Tightening the various component fixings on your Land Rover is Important so that 1) You Don’t over tighten or stress the fixing and 2) It’s tight enough so that the component can do its job correctly and safely. Use a good quality torque wrench and ensure that once used it is put back to its minimum setting to ensure that it remains accurate and the internal parts are not stressed or stretched.

ENGINE- 2.25 4 CYLINDER    lbf. Ft

Connecting rod cap nuts…………….…….25

Main bearing cap bolts (Petrol 3 brg).85

 (Diesel)……....100

Cylinder head bolt Petrol 5/16 UNF…..18

                                 ½    UNF…..65

                        Diesel 5/16 UNF…..18

                                 ½    UNF……90

Rocker shaft bolts Petrol 5/16 UNF..…18

                                  ½   UNF……65

                        Diesel 5/16 UNF……18

                                  ½   UNF……90

Starter Dog          Petrol/Diesel….……200

Flywheel bolts……..…………………….60 to 65

Oil filter bolts (Canister to housing)….12

                    (Housing to block)……25

Engine sump bolts……………………………..12

TORQUE SETTINGS

© Copyright seriesdiesellandrover.com 2013 All rights reserved

JOBS COMPLETED

HANDBRAKE

PROPSHAFT

ENGINE

STEERING

DIVIDER

FUEL TANK

GEAR STICK

FOOT BRAKE

SWIVEL HOUSING

LAND ROVER INFO

GEAR LEVERS

ENGINE TIMING

ELECTRICAL SYSTEM

LUBRICANTS

TOOLS/EQUIPMENT

VISITORS VEHICLES

VALVE CLEARANCES

EXHAUST SMOKE

GLOWPLUGS

FUEL SYSTEM 2.25 DIESEL    lbf. Ft

Injector nuts…………………………….……6 to 8

MANIFOLD+EXHAUST

Induction manifold to exhaust…….…….17

CLUTCH

Clutch cover bolts…………………….18 to 25

GEARBOX

Output drive flange nut………………………85

Layshaft bolt…(apply loctite 601)………50

REAR AXLE AND FINAL DRIVE

Hub driving flange bolt………………30 to 38

SALISBURY TYPE AXLES

Differential case bolts…….…………66 to 75

Crown wheel bolts………………..111 to 125

Diff bearing cap bolts……………..93 to 105

Diff cover bolts………………………...20 to 25

        

STEERING                              lbf. Ft

Steering wheel nut……………………………..40

Ball joint nuts………………………………………30

Relay lever pinch bolts………………………..55

Steering box to support bracket.50 to 60

Steering box support bracket to chassis bolts……………………………………………………15

Steering box drop arm nut…………60 to 80

Road wheel nuts………………………..75 to 85

SUSPENSION (ALL MODELS)

Leaf spring U bolts front and rear……….58

Shackle nuts and bolts……………..60 to 70

   

BRAKES                                 lbf. Ft

Wheel cylinder bleed nipple…………..4 to 6

Master cylinder to servo nuts……16 to 19

Tipping valve retainer (Dual system master cylinder)……………………….35 to 45

Brake failure switch end pipe union……16

Brake failure switch unit to housing……16

Fluid reservoir to master cylinder bolt (single line servo)…………….……….20 to 25

Fluid reservoir to master cylinder screws (dual line servo models)……………….2 to 3

Servo assembly securing nuts……………..9

ELECTRICAL EQUIPMENT

Alternator shaft nut…………………..25 to 30

Diesel heater plugs………………………………25

Starter through bolts…………………………….8

ROVER TYPE AXLES               lbf. Ft

Bevel pinion driving flange nut……………85

Crown wheel bolts…………………….40 to 45

Diff bearing cap bolts………………..50 to 65

Hub driving flange nut……………...10 to 15

FRONT AXLE AND FINAL DRIVE

Hub driving flange bolts…………….30 to 38

Hub driving flange nut…………….…15 to 20

Bevel pinion driving flange nut……….……85

Crown wheel bolts………………………40 to 45

Diff bearing cap bolts…………………50 to 65

Upper swivel pin bolts…………….….50 to 65

Lower swivel pin nuts…………………50 to 65

REFERENCE

CAPACITIES/WEIGHTS

IDENTIFICATION NUMBERS

TORQUE SETTINGS

PDF DOWNLOADS